ELECTRICAL COMPONENTS. 08/10/15-01/11/2016. Headlamp range control.. 2018 Audi TTS Base Coupe 2.0L A/T Quattro

Controller. from 01/11/2016. HEADLAMP RANGE CONTROL.

Controller rivet. HEADLAMP RANGE CONTROL. A Clip that holds the Headlamp Control Module in place. A Clip used on a windshield defroster nozzle. A Clip used to secure the liftgate hinge cover. A Clip which helps secure the Backup Warning System Control Module to it's mounting point. A Clip which helps secure the HVAC Electronic Control Module to it's mounting point. A Clip which helps secure the Sound Absorber to it's mounting point. A fastener which consists of a shaft and a Head on one end, and when the shaft end is installed it expands and holds the Radiator Support Splash Shield in place. A fastener which consists of a shaft and a Head on one end, and when the shaft end is installed it expands and holds the Radio Amplifier in place. A fastener which secures the Bumper Molding to it's mounting point. A fastener which secures the Instrument Panel Crossmember to it's mounting point. A Rivet to retain the License Plate Bracket to the vehicle. A securing fastener which helps hold the Defroster Trim in place. Instrument Panel Air Duct Clip. Instrument Panel Air Duct Rivet. Plastic fastener to retain speaker cover to vehicle. Quarter Panel Trim Panel Clip. Spoiler Rivet. Trunk Trim Panel Clip.

Front Left. Front sensor. Left.HEADLAMP RANGE CONTROL.

Front Right. Front sensor. Right.HEADLAMP RANGE CONTROL.

Front sensor mount bolt. Left.HEADLAMP RANGE CONTROL. Right.HEADLAMP RANGE CONTROL. A screw that is used to secure the Steering Gear Dust Shield to it's mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc) on one end used to secure the Engine Mount Heat Shield to it's mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc) on one end used to secure the Floor Pan Splash Shield to it's mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the CV Joint Splash Shield to it's mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Fender Reinforcement to it's mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Floor Pan Crossmember to it's mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Fuse & Relay Center to a mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Steering Gear Shield to its mounting surface. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Turbocharger Heat Shield to a mounting point. Engine Coolant Reservoir Bolt. Hardware to attach the Heat Shield to the catalytic converter. Headlight Level Sensor Bolt. Power Steering Pressure Line Bolt. Trunk Trim Panel Bolt. Included with: Housing.

Front sensor nut. Left.HEADLAMP RANGE CONTROL. Right.HEADLAMP RANGE CONTROL. A Nut used to secure the fuel pressure regulator to it's mounting point. A solid metal or plastic block with a threaded hole in the center which is used to secure the Hood Safety Catch to it's mounting point. A solid metal or plastic block with a threaded hole in the center which is used to secure the Seat Air Bag Inflator Module to its mounting point. A solid metal or plastic block with a threaded hole in the center which is used to tighten or adjust the Brake Cooling Duct. A solid metal or plastic block with a threaded hole in the center which is used to tighten or adjust the Cruise Control Distance Sensor. Bolt that secures the Hood Latch. Engine Cooling Fan Blade Nut. Headlight Level Sensor Nut. Hood Latch Striker Plate Nut. Part cannot be reused/reinstalled. Suspension Strut Nut. Tail Light Nut. Trim panel for the Convertible Top Stowage Compartment. Included with: Pressure regulator.

Left.HEADLAMP RANGE CONTROL. Rear Left. Rear sensor. Headlight Level Sensor. Sensor that is used to determine the height of the suspension components. Applique. Headlight Level. LevelSENSO. Linkage. Suspension Ride Height.

Rear Right. Rear sensor. Right.HEADLAMP RANGE CONTROL. Headlight Level Sensor. Sensor that is used to determine the height of the suspension components. Headlight. Linkage. SENSO. Suspension Ride Height.

Left.HEADLAMP RANGE CONTROL. Rear sensor mount bolt. Right.HEADLAMP RANGE CONTROL. A Bolt for a beam axle. A Bolt used to attach the blind spot detection warning Sensor to its mounting point. A Screw that is used to secure the Active Suspension System Height Sensor to it's mounting point. A Screw which holds the instrument panel cover to it's mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Active Suspension System Height Sensor to it's mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Liftgate Lock Actuator to it's mounting point. Headlight Level Sensor Bolt. Part cannot be reused/reinstalled.

Left.HEADLAMP RANGE CONTROL. Rear sensor nut. Right.HEADLAMP RANGE CONTROL. A Nut that attaches the Axle Beam to the sub-frame. A rubber ring with a hole in the center which provides protection through which Suspension Control Arm related components pass through. A solid metal or plastic block with a threaded hole in the center which is used to tighten or adjust the Active Suspension System Height Sensor. A solid metal or plastic block with a threaded hole in the center which is used to tighten or adjust the Door Reinforcement Bar. A solid metal or plastic block with a threaded hole in the center which is used to tighten or adjust the Door Shell. A solid metal or plastic block with a threaded hole in the center which is used to tighten or adjust the Tail Lamp Pocket. Headlight Level Sensor Bolt. Headlight Level Sensor Nut. Part cannot be reused/reinstalled. Suspension Control Arm Nut. Included with: Capacitor.